Posts Tagged ‘EBPADMA’

PMGDM / UDMA Used in Remineralization Applications

Friday, September 10th, 2010
Share This Post!

Effects of adhesive, base and diluent monomers on water sorption and conversion of experimental resins

Sabine H. Dickens, Glenn M. Flaim, Cynthia J.E. Floyd

Dental Materials Volume 26, Issue 7, Pages 675-681 (July 2010)

Objectives: To establish the relationship of resin composition and resin hydrophilicity (indicated by solubility parameters and logP) to water sorption (WS), solubility, and degree of double bond conversion (DC) of resin mixtures designed for adhesive restoratives by varying the concentration of pyromellitic glycerol dimethacrylate (PMGDM) and various co-monomers.

Methods: Sixteen resin mixtures were prepared with (30–70) mass fraction % PMGDM. At given PMGDM concentrations there were up to five compositions with increasing logP. Polymer disks (13mm×0.7mm) were exposed to 96% relative humidity (RH) to determine water sorption in humid atmosphere (WSH) and subsequently immersed in water for immersion water sorption (WSI) and solubility. DC was assessed by near infrared spectroscopy.

Results: WSI was somewhat higher than WSH, which ranged from (2.1 to 5.3) mass fraction %. Both data were positively correlated to PMGDM concentrations [Pearson correlation, p<0.02; R2=0.74, 0.73 (WSI)] and solubility (R2=0.64), but not to logP. When grouped by structural similarities, i.e., base resins with bisphenol A core (Group B), Group O containing diluent monomers, or Group U containing urethane dimethacrylate, WS within each group was inversely correlated to logP with R2=0.98, 0.81, 0.95, and WS/solubility correlation improved with R2=0.88, 0.92 and 0.75, respectively. Solubility ranging from 0.3% to 2.3% was inversely related to DC (r=−0.872). Conversion ranging from 41% to 81% was lower for resins with high base monomer concentrations and highest in mixtures with UDMA.

Significance: LogP was a good predictor of WS after grouping the resins according to functional, compositional and structural similarities. WS and conversion were reasonably well predicted from Hoy’s solubility parameters and other physical resin properties.

Link:  http://www.demajournal.com/article/S0109-5641%2810%2900066-7/abstract


Share This Post!

Optimizing Degree of Conversion, Strength, Young’s Modulus and Hardness of Bis-EMA, Bis-GMA and TEGDMA Formulations

Tuesday, April 20th, 2010
Share This Post!

Preparation and Evaluation of Dental Resin Luting Agents with Increasing Content of Bisphenol-A Ethoxylated Dimethacrylate

Rafael R. Moraes, Mário A.C. Sinhoreti, Lourenço Correr-Sobrinho, Fabrício A. Ogliari, Evandro Piva, and Cesar L. Petzhold

Journal of Biomaterials Applications, Jan 2010; vol. 24: pp. 453 – 473.

Abstract: Resin luting agents in which bisphenol-A glycidyl dimethacrylate (Bis-GMA) and/or triethylene glycol dimethacrylate (TEGDMA) are replaced with increasing amounts of bisphenol-A ethoxylated dimethacrylate are prepared. Degree of conversion (DC), diametral tensile strength (DTS), Young’s modulus (YM), Knoop hardness (KHN), film thickness (FT), water sorption (Wsp ), and solubility are evaluated. Regression analyses investigate the substitution of each monomer. The most appreciable differences are detected when TEGDMA is replaced: decreased DC, DTS, and Wsp, and increased YM, KHN, and FT. For substitution of Bis-GMA, the only significant differences are reduced Wsp and increased YM. An ideal formulation of resin cement would make use of the three monomers.

…Bis-GMA, TEGDMA, and/or Bis-EMA (Esstech Inc., Essington, PA, USA) were tested…photo-curable, 0.4 wt% of camphor- quinone (Esstech) and 0.8 wt% of N,N-dimethyl-p-toluidine…silanated strontium glass fillers (Esstech), 0.7 and 2 mm in size, to a constant…

This version was published on January 1, 2010.

Link:  http://jba.sagepub.com/cgi/content/abstract/24/5/453


Share This Post!

Esstech Inc. – Creating custom products & formulations to meet your unique needs!